All types of vehicles are prone to rusting because of the ferrous metals used to create them. Also affecting the severity and speed of rusting are the car's exposure to the elements and weather. The appearance might be bad but its effects on the structure are much worse. It's interesting to note that more vehicles are sent to junkyards due to rusting than mechanical failure. A small portion that is seen outside might mean a crater of rust on the inside. Geography ,not only climate can make a difference . If you live in a maritime area near the sea , and have salt air, this is a consideration and perhaps you should buy a new car or a more premium model than a base Chevy or GMC truck. Premium models while the metal may not be thicker - its auto industry standard - will have more layers of paint as well as rust protective finishes.
Upon purchase of a brand new car, there is a standard factory undercoating and rustproofing limited to some surfaces. The buyer has to request this from the manufacturer. More often than not, this is inadequate. Unfinished metal surfaces of the car are treated with a petroleum-based compound. Rustproofing is considered a good investment for people who don't buy and sell automobiles often. The most ideal time to do so is when the vehicle is around three months old or has traveled 3,000 miles only. After that, complete protection even after rustproofing would be difficult because moisture might have already seeped in grime and hard to reach areas. It's also unwise to do so after the vehicle has been exposed to salt water. Yet all in all it might be better to bite the bullet. Rather than be out shopping at auto dealers lot for low km clean used trucks in Vancouver BC, it might just be simpler and better economy overall to buy that spanking brand new Chevrolet , GMC or even foreign built Toyota vehicle ,taking the short drive to Surrey.
The kit contains detailed instructions and has enough material for a full-size car. The whole process, including cleaning and drying, will take 4-5 hours. Wear goggles to protect your eyes and have two sets of old clothes to change in. Rustproofing should not be done in humid weather when metal parts are damp. Do not treat any section that emits heat like the engine, radiator core, manifold, exhaust pipes, catalytic converter, drive shaft, manifold, and transmission. Seals, tubes, and gaskets can become brittle as it is the effect on rubber. This includes tires which should be covered in plastic or thick towels. Should you spill some on yourself, kerosene or a mineral solvent can remove it easily.
Do not apply to areas which are exposed to heat, like the engine, transmission, driveshaft, manifold, exhaust, pipes, catalytic converter, and radiator core. Rubber seals, tubes and gaskets because it makes them brittle. Don't start the process during very humid days when surfaces are damp.
Prior to application, get a professional steam engine-clean. Use a wire brush to remove loose dirt and rust. Drain holes must be cleared. Prepare safety jacks so that the underbody can be treated. Be sure to include the exterior removable trims on the car like, holes and clips. You are on your way to a rust-free vehicle!
Upon purchase of a brand new car, there is a standard factory undercoating and rustproofing limited to some surfaces. The buyer has to request this from the manufacturer. More often than not, this is inadequate. Unfinished metal surfaces of the car are treated with a petroleum-based compound. Rustproofing is considered a good investment for people who don't buy and sell automobiles often. The most ideal time to do so is when the vehicle is around three months old or has traveled 3,000 miles only. After that, complete protection even after rustproofing would be difficult because moisture might have already seeped in grime and hard to reach areas. It's also unwise to do so after the vehicle has been exposed to salt water. Yet all in all it might be better to bite the bullet. Rather than be out shopping at auto dealers lot for low km clean used trucks in Vancouver BC, it might just be simpler and better economy overall to buy that spanking brand new Chevrolet , GMC or even foreign built Toyota vehicle ,taking the short drive to Surrey.
The kit contains detailed instructions and has enough material for a full-size car. The whole process, including cleaning and drying, will take 4-5 hours. Wear goggles to protect your eyes and have two sets of old clothes to change in. Rustproofing should not be done in humid weather when metal parts are damp. Do not treat any section that emits heat like the engine, radiator core, manifold, exhaust pipes, catalytic converter, drive shaft, manifold, and transmission. Seals, tubes, and gaskets can become brittle as it is the effect on rubber. This includes tires which should be covered in plastic or thick towels. Should you spill some on yourself, kerosene or a mineral solvent can remove it easily.
Do not apply to areas which are exposed to heat, like the engine, transmission, driveshaft, manifold, exhaust, pipes, catalytic converter, and radiator core. Rubber seals, tubes and gaskets because it makes them brittle. Don't start the process during very humid days when surfaces are damp.
Prior to application, get a professional steam engine-clean. Use a wire brush to remove loose dirt and rust. Drain holes must be cleared. Prepare safety jacks so that the underbody can be treated. Be sure to include the exterior removable trims on the car like, holes and clips. You are on your way to a rust-free vehicle!
About the Author:
After market kits are available to apply rustproofing compounds both to external surfaces & nside enclosed sections such as sills/rocker panels , through either existing or specially drilled holes. The compounds are usually wax-based and applied by pressure spray, but phosphoric acid can also be painted on already rusted areas. Link to home page here for Surrey BC & Vancouver auto buyers new & low km used.